Mullite-bonded SiC-whisker-reinforced SiC matrix composites: Preparation,characterization, and toughening mechanisms

A novel mullite-bonded SiC-whisker-reinforced SiC matrix composite (SiCw/SiC, SiC whisker-to-SiC powder mass ratio of 1:9) was designed and successfully prepared. Before preparing the composite, the inexpensive lab-made SiCw was first modified by an oxidation/leaching process and then coated with Al₂O₃. The kinetics results indicate that the oxidation process can be described by improved shrinking-cylinder models. The aspect ratio of SiCw improved after modification. Subsequently, raw materials with a SiC–SiO₂–Al₂O₃ triple-layered structure were obtained after the Al₂O₃-coating process and used as feedstocks during the subsequent hot-pressing sintering. Finally, the characterization of the composites indicates that the mullite-bonded sample performs better (relative density of 93.8?±?1.4%, flexural strength of 533.3?±?18.2?MPa, fracture toughness of 13.6?±?2.1?MPa?m^1/2, and Vickers hardness of 20.6?±?2.5?GPa) than the reference sample without the mullite interface. The improved toughness could essentially be attributed to the moderately strong interface bonding and effective load transfer effects of the mullite interface.     

纳米银-聚合物薄膜的制备及力电性能测试

聚合物基底上纳米银颗粒薄膜的制备工艺相对简单,成本较低,且该薄膜具有成为高敏感性压阻应力/应变传感材料的潜力。本文采用银镜制备法在聚酰亚胺(PI)和聚乙烯(PE)上合成了纳米银颗粒薄膜,系统研究了该薄膜制备工艺、结构特性、材料性能之间的关系。实验考察了材料“浸泡”时间及聚合物材料前处理等因素对材料表面吸附纳米颗粒含量的影响,研究了 “浸泡”时间对纳米银颗粒粒径大小、颗粒含量及分布的影响,并探讨了不同聚合物基体的颗粒特性对薄膜二维导电渗滤,压阻特性及拉伸性能的影响。研究表明,增加“浸泡”时间能够增加纳米银颗粒粒径大小,提高银颗粒的含量及分布均匀性；在相同的制备条件下,PI基底较PE基底对纳米银颗粒具有更加优异的吸附效果；在PI 和PE基底上的纳米银颗粒薄膜均表现出显著的压阻性能,且电阻对应变的敏感性随应变的增大及银颗粒含量的减少而显著提高。     

金属有机框架材料MIL-53(Al)-F127对双酚A的吸附性能

采用一步溶剂热法制备具有介孔结构金属有机框架材料MIL-53(Al)-F127，用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射仪(XRD)、傅里叶红外变换光谱仪(FTIR)、全自动比表面积及孔隙度分析仪(BET)等手段表征其形貌和结构，探究其对双酚A(BPA)的吸附性能并与微孔结构的MIL-53(Al)对比，研究了吸附剂的含量、pH以及温度对其吸附性能的影响。结果表明，介孔结构金属有机框架材料MIL-53(Al)-F127对双酚A具有良好的吸附性能；在pH值为6、温度为30℃条件下MIL-53(Al)-F127在20 min左右达到最大平衡吸附量为27.2 mg/g，去除率达到92%。其吸附动力学模型拟合结果，符合准二级动力学曲线。     

Effect of carbon nanotubes on structure and properties of the antifriction coatings produced by plasma cladding

Abstract

Due to their high antifriction characteristics, the Sn-Sb-Cu alloys (referred to as babbits) are widely used to coat sliding bearings. However, some limitations of the present techniques for applying such coating materials cause a decrease in their fatigue strength because of the reinforcing phase particles growth. As a technique for restricting the increasing of the reinforcing particle sizes, this paper proposes plasma surface cladding with multiwall carbon nanotubes (MWNTs) as modifiers. The dry sliding friction tests performed according to the “pin-on-disk” scheme using as a counterface a steel 100Cr6 (DIN 17230) disk have shown that adding to the coating 0.25%wt of CNTs significantly improves the friction stability (the coefficient of friction process stability decreases twice with reducing the friction coefficient and wear resistance by 5% on the average). An attempt to reveal the mechanism for the MWNT influence on the structure and performance of the babbit-based coatings was undertaken. Studies of the coatings metal structure by soft X-ray absorption spectroscopy and also by the metallographic and fractographic analysis involving electron-microscopy have shown that MWNTs remain stable during plasma cladding process and save into the coating.     

Flutter of delaminated three-phase nano-composite beam-plates

ABSTRACT

In this article the supersonic flutter instability of delaminated carbon nanotube reinforced three-phase composite plate is investigated. The classical laminate plate theory and piston aerodynamic theory are developed to construct the governing equation of delaminated three-phase nano-composite plates. The effective material properties are obtained using Halpin-Tsai relation and rule of mixture. The effects of different parameters including carbon nanotubes (CNTs) weight percentage, fiber volume fraction, CNTs aspect ratio and different fiber orientation on flutter pressure of delaminated reinforced composite plates are considered. According to the results, appending small amount of CNTs (4% wt) into the matrix epoxy can improve the flutter critical pressure by 33% in comparison to the neat matrix epoxy.     

Preparation and mechanism of active Mo–Mn metallization on ZTA particles surface and interfacial bonding of reinforced iron matrix composite

ZrO₂ toughened Al₂O₃ particles (ZTAp) have poor wettability with iron, and therefore some defects are easily formed at the interface between ZTAp and iron matrix, which may lead to material failure. This paper illustrates that the ZTAp were modified on the surface by the active Mo–Mn metallization, and thus, they were used as the reinforcing phases to prepare the iron-matrix composite (ZTAp/Fe composite). It is concluded that the sponge-like skeleton structure was formed on the surface of ZTAp after the metallization. The interface of ZTAp/Fe composite, which has been proved to have bearing and transitional capacity by scratch test, was formed by chemical bonding with elemental diffusion, besides mechanical bonding. The metallization mechanism of elemental diffusion can be explained by the migration of glass phase, and the elements diffusion between the interface and iron matrix is to form solid solution.     

Review on nano-and microfiller-based polyamide 6 hybrid composite: Effect on mechanical properties and morphology

Polyamide 6 (PA6)-based composites are of evolving interest due to its high strength, wear resistance, and barrier properties. The use of binary composites mostly with nanomaterial and glass fibers has been reviewed and presented in literature. However to obtain a balance of properties like stiffness, toughness, and strength along with cost reduction, ternary composites of PA6 have been designed. To achieve the balance, PA6 blend-based composites, with combination of microfiller/nanofiller or PA6 with combination micro-microfiller, PA6 with microfiller/nanofiller and fiber have been designed. The properties of PA6-based ternary hybrid composites depend on type of dispersed phase used, presence of compatibilizer, type of filler used (nanofiller or microfiller or fiber or hybrid) and combination of fillers used. However, a review in this direction is not available in literature. Here, in this study, an overall understanding of various fillers, dispersed phase, and their combinations can be understood along with the discussion on effect of these on tensile properties and morphology of hybrid composite. In this study, an attempt has been made to review the various fillers and dispersed phase and their combinations which have been used in designing the PA6 hybrid composite with good balance of stiffness, toughness, and strength.     

高密度聚乙烯/铅硼复合材料屏蔽性能和力学性能研究

研究了高密度聚乙烯/铅硼复合材料的屏蔽性能和力学性能，通过屏蔽仿真比较了密度及碳化硼（B4C）含量对屏蔽性能的影响，通过试验比较了B4C含量对屏蔽性能、弯曲强度及冲击强度的影响。仿真结果表明,随聚乙烯/铅硼复合材料密度升高，快中子屏蔽性能下降，热中子屏蔽性能和γ屏蔽性能提高；保持聚乙烯/铅硼复合材料密度不变，随B4C含量的提高，中子屏蔽性能提高而γ屏蔽性能下降;实验数据表明,随B4C含量的升高，高密度聚乙烯/铅硼材料的快中子屏蔽性能、热中子屏蔽性能升高，γ屏蔽系数下降，冲击强度和弯曲强度下降明显，屏蔽性能测试结果和仿真结果规律性相符；综合仿真结果和实验数据表明，含B4C 2 %左右的高密度聚乙烯/铅硼复合材料同时具有较好的屏蔽性能和力学性能。